BJ368MO

DESCRIPTION BJ368MO is a heterophasic copolymer characterized by very high flow, and optimum combination of high stiffness and impact strength. The material is nucleated with Borstar Nucleation Technology (BNT). Flow properties, nucleation and good stiffness give potential for cycle time reduction.   The material has both good antistatic performance and mould release properties. APPLICATIONS Thin wall containers               Food packaging Small size ice cream containers   SPECIAL FEATURES Very good stiffness and impact balance   Good flow behaviour Reduced cycle time and increased output PHYSICAL PROPERTIES Property       Density Melt Flow Rate (230°C/2.16kg) Tensile Modulus (1mm/min) Tensile Strain at Yield (50mm/min) Tensile Stress at Yield (50mm/min) Flexural Modulus   Tensile Strain at Yield   Tensile Stress at Yield   Flexural Modulus(by 1% secant)   Charpy Impact Strength, notched (23°C) Charpy Impact Strength, notched (-20°C) IZOD Impact Strength, notched (23°C) IZOD Impact Strength, notched (-20°C) Heat Deflection Temperature(0,45MPa)** Vicat Softening Temperature(Method A)*** Hardness, Rockwell(R-scale) Typical Value   900-910kg/m³ 70g/10min 1500MPa 4% 25MPa 1500MPa 4% 25MPa 1450MPa 5,5kJ/m² 3,5kJ/m² 55J/m 40J/m 102°C 150°C 92 Test Method ISO 1183 ISO 1133 ISO 527-2 ISO 527-2 ISO 527-2 ISO 178 ASTM D638 ASTM D638 ASTM D790A ISO 179/1eA ISO 179/1eA ASTM D256 ASTM D256 ISO 75-2 ISO 306 ISO 2039-2 *Data should not be used for specification work **Measured on injection moulded specimens acc. to ISO 1873-2 *** Measured on injection moulded specimens, conditioned at 23°C and 50% Rel. Hum. PROCESSING CONDITIONS   BJ368MO is easy to process with standard injection moulding machines. Following parameters should be used as guidelines: Melt temperature:   210 - 260°C Holding pressure: Mould temperature: Injection speed:   200 - 500bar    As required to avoid sink marks 10 - 30°C As high as possible Shrinkage 1 - 2%, depending on wall thickness and moulding parameters STORAGE BJ368MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.                                                                               information on storage can be found in Safety Information Sheet (SIS) for this product SAFETY More The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative. RECYCLING The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling. RELATED DOCUMENTS The following related documents are available on request, and represent various aspects on the usability, safety, recovery and disposal of the product. Safety Information Sheet Statement on chemicals, regulations and standards Statement on compliance to food contact regulations   STANDARDS Borouge is certified to various ISO standards, please refer to Borouge.com for more information. DISCLAIMER The product(s) mentioned herein are not intended to be used for medical, pharmaceutical or healthcare applications and we do not support their use for such applications. To the best of our knowledge, the information contained herein is accurate and reliable as of the date of publication, however we do not assume any liability whatsoever for the accuracy and completeness of such information.   Borouge makes no warranties which extend beyond the description contained herein. Nothing herein shall constitute any warranty of merchantability or fitness for a particular purpose.   It is the customer's responsibility to inspect and test our products in order to satisfy itself as to the suitability of the products for the customer's particular purpose. The customer is responsible for the appropriate, safe and legal use, processing and handling of our products. No liability can be accepted in respect of the use of Borouge products in conjunction with other materials. The information contained herein relates exclusively to our products when not used in conjunction with any third party materials.