Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Hazards Identification Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity
Home > Pigment Green 36 > Pigment Green 36(14302-13-7)

Pigment Green 36(14302-13-7)

Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Hazards Identification Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity

Product Identification

Product Name
Pigment Green 36
Synonyms
29H,31H-Phthalocyanine, 1,3,8,16,18,24-hexabromo-2,4,9,10,11,15,17,22,23,25-decachloro-, copper complex
Copper, (1,3,8,16,18,24-hexabromo-2,4,9,10,11,15,17,22,23,25-decachlorophthalocyaninato(2-))
Fastogen Green Y
Hostaperm Green 8G
Lionol Green 6YKP
Vynamon Green 6Y
CAS
14302-13-7
Formula
C32Br6Cl10CuN8
Molecular Weight
1393.9
EINECS
238-238-4
RTECS
GL7500000
RTECS Class
Mutagen
Beilstein/Gmelin
NA

Physical and Chemical Properties

Appearance
Odorless green-yellowish to green powder.
Usage
Painting and drawing pigment.

First Aid Measures

Ingestion
Seek medical attention. If individual is drowsy or unconscious, do not give anything by mouth; place individual on the left side with the head down. Contact a physician, medical facility, or poison control center for advice about whether to induce vomiting. If possible, do not leave individual unattended.
Inhalation
IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used.
Skin
IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
Eyes
First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Handling and Storage

Storage
Keep in a cool, dry, dark location in a tightly sealed container or cylinder. Keep away from incompatible materials, ignition sources and untrained individuals. Secure and label area. Protect containers/cylinders from physical damage.
Handling
All chemicals should be considered hazardous. Avoid direct physical contact. Use appropriate, approved safety equipment. Untrained individuals should not handle this chemical or its container. Handling should occur in a chemical fume hood.

Hazards Identification

Ingestion
See inhalation.
Inhalation
Inhalation of the dusts and mists from this type of compound can cause nasal mucous membrane irritation.
Skin
See inhalation.
Eyes
See inhalation
Hazards
Flash point data for this chemical are not available, but it is probably non-flammable.

Exposure Controls/Personal Protection

Personal Protection
Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Whre chemical resistant gloves. To prevent repeated or prolonged skin contact, wear impervious clothing and boots.
Respirators
Wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter.

Fire Fighting Measures

Fire Fighting
Fires involving this compound should be controlled with a dry chemical, carbon dioxide or Halon extinguisher. A water spray can also be used on this chemical.

Accidental Release Measures

Small spills/leaks
If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then dampen the solid spill material with toluene, then transfer the dampened material to a suitable container. Use absorbent paper dampened with toluene to pick up any remaining material. Your contaminated clothing and absorbent paper should be sealed in a vapor-tight plastic bag for eventual disposal. Solvent-wash all contaminated surfaces with toluene followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

Stability and Reactivity

Incompatibilities
Incompatible with oxidizing and reducing agents.
Stability
No data.
Contact More