Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Hazards Identification Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity
Home > 2-(p-Nitrophenyl)ethanol > 2-(p-Nitrophenyl)ethanol(100-27-6)

2-(p-Nitrophenyl)ethanol(100-27-6)

Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Hazards Identification Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity

Product Identification

Product Name
2-(p-Nitrophenyl)ethanol
Synonyms
2-(4-Nitrophenyl)ethanol
2-(p-Nitrophenyl)ethanol
4-Nitrophenethyl alcohol
p-Nitrophenethyl alcohol
CAS
100-27-6
Formula
C8H9NO3
Molecular Weight
167.16
EINECS
202-835-8
RTECS
SG8602000
RTECS Class
Mutagen
Beilstein/Gmelin
1866148
Beilstein Reference
4-06-00-03083

Physical and Chemical Properties

Appearance
Yellow needles (from aqueous methanol) or orange solid.
Solubility in water
Slightly soluble
Melting Point
64
Boiling Point
321
Vapor Pressure
0.0001 (25 C)
Density
1.31 g/cm3
Partition Coefficient
1.09
Heat Of Vaporization
59.4 kJ/mol

First Aid Measures

Ingestion
DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician.
Inhalation
IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used.
Skin
IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
Eyes
First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Handling and Storage

Storage
Keep in a cool, dry, dark location in a tightly sealed container or cylinder. Keep away from incompatible materials, ignition sources and untrained individuals. Secure and label area. Protect containers/cylinders from physical damage.
Handling
All chemicals should be considered hazardous. Avoid direct physical contact. Use appropriate, approved safety equipment. Untrained individuals should not handle this chemical or its container. Handling should occur in a chemical fume hood.

Hazards Identification

Ingestion
See inhalation.
Inhalation
Structurally similar chemicals may cause methemoglobinemia.
Skin
See inhalation.
Eyes
See inhalation

Exposure Controls/Personal Protection

Personal Protection
Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Whre chemical resistant gloves. To prevent repeated or prolonged skin contact, wear impervious clothing and boots.
Respirators
Wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter.

Fire Fighting Measures

Flash Point
145
Fire Fighting
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher.
Fire Potential
This material is probably combustible.

Accidental Release Measures

Small spills/leaks
Should a spill occur while you are handling this chemical, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with 60-70% ethanol and transfer the dampened material to a suitable container. Use absorbent paper dampened with 60-70% ethanol to pick up any remaining material. Seal the absorbent paper, and any of your clothes, which may be contaminated, in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

Stability and Reactivity

Incompatibilities
Flammable and/or toxic gases are generated by combination with with alkali metals, nitrides, and strong reducing agents Reacts with oxoacids and carboxylic acids to form esters plus water Incompatible with oxidizing agents.
Stability
No data.
Contact More