Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity
Home > 2,6-Dimethyl-2-hepten-7-al > 2,6-Dimethyl-2-hepten-7-al(106-72-9)

2,6-Dimethyl-2-hepten-7-al(106-72-9)

Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity

Product Identification

Product Name
2,6-Dimethyl-2-hepten-7-al
Synonyms
Acetic acid, (3-methylbutoxy)-, 2-propenyl ester
Allyl (3-methylbutoxy)acetate
Prop-2-enyl 2-(3-methylbutoxy)acetate
CAS
67634-00-8
Formula
C10H18O3
Molecular Weight
186.25
EINECS
266-803-5
Beilstein/Gmelin
NA

Physical and Chemical Properties

Appearance
Clear colorless liquid.
Melting Point
-23
Boiling Point
218
Density
0.941 g/cm3 (20 C)
Partition Coefficient
1.88

First Aid Measures

Ingestion
If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician.
Inhalation
IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used.
Skin
IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
Eyes
First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.

Handling and Storage

Storage
Keep in a cool, dry, dark location in a tightly sealed container or cylinder. Keep away from incompatible materials, ignition sources and untrained individuals. Secure and label area. Protect containers/cylinders from physical damage.
Handling
All chemicals should be considered hazardous. Avoid direct physical contact. Use appropriate, approved safety equipment. Untrained individuals should not handle this chemical or its container. Handling should occur in a chemical fume hood.

Exposure Controls/Personal Protection

Personal Protection
Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Whre chemical resistant gloves. To prevent repeated or prolonged skin contact, wear impervious clothing and boots.
Respirators
Where the neat test chemical is stored, weighed and diluted, wear an approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter.
Exposure Effects
The toxicological properties of this material have not been investigated.

Fire Fighting Measures

Fire Fighting
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher.
Fire Potential
This chemical is combustible.

Accidental Release Measures

Small spills/leaks
If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION. Then, use absorbent paper to pick up all liquid spill material. Your contaminated clothing and absorbent paper should be sealed in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.

Stability and Reactivity

Incompatibilities
May react with strong oxidizing acids sufficiently exothermically to ignite the reaction products.
Stability
No data.
Contact More