Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Hazards Identification Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity
Home > Orange sweet oil > Orange sweet oil(8008-57-9)

Orange sweet oil(8008-57-9)

Supplier Product Identification Physical and Chemical Properties First Aid Measures Handling and Storage Hazards Identification Exposure Controls/Personal Protection Fire Fighting Measures Accidental Release Measures Stability and Reactivity

Product Identification

Product Name
Orange sweet oil
Synonyms
Neat oil of sweet orange
Neroli oil
Oil of sweet orange
Orange oil
CAS
8008-57-9
RTECS
RI8600000
RTECS Class
Tumorigen; Natural Product; Primary Irritant
Beilstein/Gmelin
NA

Physical and Chemical Properties

Appearance
Yellow to orange liquid with a citrus aroma.
Density
0.8728 g/cm3
Usage
Flavor and perfume.
Refractive Index
1.467

First Aid Measures

Ingestion
First aid is not normally required. If symptoms develop, seek medical attention.
Inhalation
If symptoms develop, move individual away from exposure and into fresh air. If symptoms persist, seek medical attention. If breathing is difficult, administer oxygen. Keep person warm and quiet; seek immediate medical attention.
Skin
Remove contaminated clothing. Wash exposed area with soap and water. If symptoms persist, seek medical attention. Launder clothing before reuse.
Eyes
If symptoms develop, immediately move individual away from exposure and into fresh air. Flush eyes gently with water for at least 15 minutes while holding eyelids apart; seek immediate medical attention.

Handling and Storage

Storage
Keep tightly closed in a cool place in a tightly closed container.
Handling
Containers of this material may be hazardous when emptied. Since emptied containers retain product residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be observed.

Hazards Identification

Inhalation
Breathing of vapor or mist is possible. Breathing small amounts of this material during normal handling is not likely to cause harmful effects. Breathing large amounts may be harmful.
Skin
May cause mild skin irritation. Prolonged or repeated contact may dry the skin. Symptoms may include redness, burning, drying and cracking of skin, and skin burns. This material is unlikely to pass into the body through the skin.
Eyes
Can cause eye irritation. Symptoms include stinging, tearing, redness, and swelling of eyes.
Ingestion
Swallowing this material is not likely to be harmful.
Hazards
Vapors are heavier than air and may travel along the ground or be moved by ventilation and ignited by heat, pilot lights, other flames and ignition sources at locations distant from material handling point. Never use welding or cutting torch on or near drum (even empty) because product (even just residue) can ignite explosively. Dense smoke may be generated while burning.

Exposure Controls/Personal Protection

Personal Protection
Chemical splash goggles in compliance with OSHA regulations are advised; however, OSHA regulations also permit other type safety glasses. Whre chemical resistant gloves. To prevent repeated or prolonged skin contact, wear impervious clothing and boots.
Respirators
If overexposure has been determined or documented, a NIOSH/MSHA jointly approved air supplied respirator is advised in absence of proper environmental control. OSHA regulations also permit other NIOSH/MSHA respirators under specified conditions.
Exposure Effects
Symptoms of exposure to this material through breathing, swallowing, and/or passage of the material through the skin may include: irritation (nose, throat, airways).

Fire Fighting Measures

Flash Point
49
Fire Fighting
Extinguish fire using regular foam, carbon dioxide, dry chemical. Wear a self-contained breathing apparatus with a full facepiece operated in the positive pressure demand mode with appropriate turn-out gear and chemical resistant personal protective equipment.

Accidental Release Measures

Small spills/leaks
Small Spill - Absorb liquid on vermiculite, floor absorbent or other absorbent material. Large Spill - Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Stop spill at source. Prevent from entering drains, sewers, streams or other bodies of water. Prevent from spreading. If runoff occurs, notify authorities as required. Pump or vacuum transfer spilled product to clean containers for recovery. Absorb unrecoverable product. Transfer contaminated absorbent, soil and other materials to containers for disposal.

Stability and Reactivity

Incompatibilities
Acids, flourides, halogens, iodine, peroxides strong oxidizing agents, vinyl- and styrene-based plastics, Avoid high temperature contact with reactive monomers (i.e., methacrylates or vinyl chloride).
Stability
Stable.
Decomposition
Oxides of carbon.
Contact More