1,1,1,2,3,4,4,5,5,5-デカフルオロ-3-メトキシ-2-(トリフルオロメチル)ペンタン

危険有害性情報のコード(GHS)

• 絵表示(GHS)

  

• 注意喚起語

  Warning

• 危険有害性情報

  H315：皮膚刺激

  H319：強い眼刺激

  H335：呼吸器への刺激のおそれ

• 注意書き

  P261：粉じん/煙/ガス/ミスト/蒸気/スプレーの吸入を避ける こと。

  P271：屋外または換気の良い場所でのみ使用すること。

  P280：保護手袋/保護衣/保護眼鏡/保護面を着用するこ と。

1,1,1,2,3,4,4,5,5,5-デカフルオロ-3-メトキシ-2-(トリフルオロメチル)ペンタン 価格

1,1,1,2,3,4,4,5,5,5-デカフルオロ-3-メトキシ-2-(トリフルオロメチル)ペンタン 化学特性,用途語,生産方法

• 外観

  無色～ほとんど無色透明液体

• 説明

  Fluorinated liquid 1,1,1,2,3,4,4,5,5,5,-Decafluoro-3-methoxy-2-(trifloromethyl)pentane is a kind of heat stable, perfluorinated liquid mainly used as industrial and conductive liquid. Due to its chemical inertness, 1,1,1,2,3,4,4,5,5,5,-Decafluoro-3-methoxy-2-(trifloromethyl)pentane can be used as single-phase or two-phase coolant for supercomputer systems and military sensitive electronic components. Because of its very high insulation, it can be used to cool high-voltage transformers and high-power electronic components. In the semiconductor industry, this liquid is used primarily as a constant temperature coolant for etching equipment, ion implantation equipment and chemical vapour deposition (CVD). Because the pour point of 1,1,1,2,3,4,4,5,5,5,-Decafluoro-3-methoxy-2-(trifloromethyl)pentane is very low, It can be used for cold and hot shock test and other tests.

• 使用

  1,1,1,2,2,3,4,5,5,5-Decafluoro-3-methoxy-4-(trifluoromethyl)pentane is used in preparation method of isolated Hydrofluoroether.

• 合成

  1,1,1,2,3,4,4,5,5,5,-Decafluoro-3-methoxy-2-(trifloromethyl)pentane is prepared by the reaction of Methyl methanesulfonate and perfluoro-2,3-epoxy-2-methylpentane. The specific synthesis steps are as follows:
  (1). Clean and dry the 500ml reaction flask first; (2). Add 200mL of diethylene glycol dimethyl ether to the flask, turn on the stirring, and add 58g (1mol) of anhydrous potassium fluoride and 52.86g (0.2mol) of 18-crown-6 under stirring; (3). Stir for 10 minutes to fully dissolve anhydrous potassium fluoride and 18-crown ether-6, then add 158g (0.5mol) of perfluoro-2-methyl 2,3-epoxypentane to obtain a solution; (4). Heat the solution water bath to 50°C, keep the temperature constant at about 50°C, slowly add 71.59g (0.65mol) methyl methanesulfonate dropwise with a dropping funnel; (5). Control the dropping time of methyl methanesulfonate for about 2h. After the dropping, the solution will continue to be kept at a constant temperature of 50°C for 3h; (6). After the reaction is completed, cool to room temperature, and then take out the mixed liquid for rectification to obtain the product. Result: The mass of hydrofluoroether obtained is 164.22g, of which 1,1,1,2,2,3,4,5,5,5-decafluoro-3-methoxy-4-(trifluoromethyl)-pentane The content is 96.79%, the residue of perfluoro-2-methyl 2,3-epoxypentane is 0.07%, the conversion rate of perfluoro-2-methyl 2,3-epoxypentane is 99.93%, 1,1,1 The yield of 2,2,3,4,5,5,5-decafluoro-3-methoxy-4-(trifluoromethyl)-pentane was 90.83%.
  

1,1,1,2,3,4,4,5,5,5-デカフルオロ-3-メトキシ-2-(トリフルオロメチル)ペンタン 生産企業

Global(144)Suppliers

132182-92-4, 1,1,1,2,3,4,4,5,5,5-デカフルオロ-3-メトキシ-2-(トリフルオロメチル)ペンタン キーワード