ポリイミド

危険有害性情報のコード(GHS)

• 絵表示(GHS)

  

• 危険有害性情報

  H315：皮膚刺激

  H319：強い眼刺激

  H335：呼吸器への刺激のおそれ

• 注意書き

  P261：粉じん/煙/ガス/ミスト/蒸気/スプレーの吸入を避ける こと。

  P304+P340：吸入した場合：空気の新鮮な場所に移し、呼吸しやすい 姿勢で休息させること。

  P305+P351+P338：眼に入った場合：水で数分間注意深く洗うこと。次にコ ンタクトレンズを着用していて容易に外せる場合は外す こと。その後も洗浄を続けること。

  P405：施錠して保管すること。

ポリイミド 価格

ポリイミド 化学特性,用途語,生産方法

• 性質

  ジメチルホルムアミド，ポリリン酸，濃硫酸に溶ける。ほかに，ポリフェニレントリアゾール，ポリイミド，ポリオキサジアゾールなどの耐熱性繊維がある。［セルロース系半合成繊維］セルロースをアセチル化して有機溶媒に可溶のアセテートまたはトリアセテートを作り，それぞれアセトン，塩化メチレン溶液から乾式紡糸したものである。

• 用途

  をもつポリマー．とくに芳香族のポリイミドは耐熱性の要求されるフィルム，プリント基板，電線エナメルなどに使用される．代表的なものは，無水ピロメリト酸と芳香族ジアミンとの反応によるもので，短時間なら500 ℃ の高温に耐える．

• 使用

  Polyimides (PI, also known by alternative brand names: Pyralin Apical, Kapton, and Kaptrex) are polymers made of imide monomers (two carbonyl groups bonded to nitrogen). It has a density of 1430 kg/m3, Young’s modulus 3200 MPa, tensile strength (75–90) MPa, glass transition temperature > 400℃, thermal conductivity of 0.53 W/(m K), and a low relative dielectric constant of 2.9. Polyimides have applications similar to BCBs and also find applications as a low dielectric constant material in high-frequency interconnects (low-k material). The higher thermal conductivity and high glass transition temperature when compared to other types of insulating polymers also makes them a good choice where heat dissipation is important or other applications requiring good thermal management or low parasitic capacitances. Microchannels and high-frequency microdevices embedded in both photosensitive and nonphotosensitive polyimides have been fabricated and reported.

• 化学性质

  耐候性，耐薬品性，光沢性

• 工業用途

  Available both as thermoplastic and thermosetresins, polyimides (PIs) are a family of someof the most heat- and fire-resistant polymersknown. Moldings and laminates are generallybased on thermoset resins, although some aremade from thermoplastic grades. Unlike mostplastics, polyimides are available as laminatesand shapes, molded parts, and stock shapesfrom some materials producers. Thin-film products— enamel, adhesives, and coatings — areusually derived from thermoplastic polyimideresins.
  Polyimide parts and laminates can serve continuouslyin air at 260°C; service temperaturefor intermittent exposure can range from cryogenicto as high as 482°C. Glass-fiber-reinforcedversions retain over 70% of their flexuralstrength and modulus at 249°C. Creep is almostnonexistent, even at high temperatures, anddeformation under load (27.2 MPa) is less than0.05% at room temperature for 24 h.
  These materials have good wear resistanceand low coefficients of friction, both of whichare further improved by polytetrafluoroethylenefillers. Self-lubricating parts containing graphitepowders have flexural strengths above 68MPa, which is considerably higher than thoseof typical thermoplastic bearing compounds.
  Electrical properties of polymide moldingsare outstanding over a wide range of temperatureand humidity conditions.

ポリイミド 上流と下流の製品情報

ポリイミド 生産企業

Global(86)Suppliers

62929-02-6, ポリイミド キーワード