Overview
Methyl 4-tert-butylbenzoate appears as white crystalline powder, being slightly soluble in water with the water solubility of 0.006g/100ml Water at 20 ° C. It can be miscible in ethanol, ether and other organic solvents with the organic toluene solubility of 9.0%, being an important organic synthesis intermediates. It is an important additive during the production of PVC heat stabilizer, PP nucleating agent, sunscreen and scaling powder. As the alkyd resin modifier, it can improve the resin luster, color, and speed up the resin drying time and improve the chemical resistance of the performance. The ammonium salt can improve the performance of friction parts and prevent rust, thus can be used as the additives of cutting oil and lubricants. Its sodium salt, barium salt, zinc salt can be used as polymer stabilizer and nucleating agent.
Synthesis method
The synthesis method of P-tert-butyl benzoic acid includes:
The oxidation method of liquid phase solvent, take acetic acid as solvent, lead acetate as oxidant and synthesize p-tert-butyl benzoic acid at low temperature.
Liquid non-solvent oxidation method: there is no need of any solvent; take cobalt acetate and sodium bromide as a catalyst and apply air oxidation at 170e temperature to obtain the final products.
High temperature gas phase oxidation method, in the presence of catalyst, high temperature lead to vaporization and oxidation of p-tert-butyl toluene to generate p-tert-butyl benzoic acid.
Recently, we found that there is no need of any catalyst if using cheap nitric acid as the oxidant for oxidation of p-tert-butyl toluene to get the crude t-butyl benzoic acid, followed by being dissolved with sodium hydroxide to remove organic impurities and insoluble matter, and then being acidified to obtain pure p-tert-butyl benzoic acid. This method has good selectivity and low energy consumption, and can avoid the shortcomings of air oxidation method such as low oxidation conversion rate, thus having great practical value.
Preparation of crude p-tert-butyl benzoic acid:
To a 500 mL autoclave, add 26 mL (0.2 mol, 29.6 g) of p-tert-butyltoluene, 26 mL 68% nitric acid (0.4 mol, 37 g) and 2.5 mL of water. The reaction stirrer was started and the temperature was raised to 180e. The reaction lasted for 8 hour followed by cooling with cool water. Open the reactor with most of the solid being deposited on the bottom of the reactor and attached to the reactor cooling tube in a small amount. The solid was collected, filtered and dried to give 34.5 g with a yield of 95.5%.
The purification of P-tert-butylbenzoic acid
Weigh 10 g of sodium hydroxide and add 90 mL of water to prepare a 10% sodium hydroxide solution. Add the above solid into it. After being sufficiently dissolved, the filtrate was adjusted to pH 3 with hydrochloric acid, and a large amount of crystals would be precipitated at this time. The solution was allowed to stand for 33.4 g with a yield of 98.2%. The product was analyzed by infrared spectroscopy, displaying the characteristic peaks of p-tert-butylbenzoic acid. The content was 98.4% by HPLC analysis with a melting point of 164~166e (literature values 164~165e).
The effect of nitric acid concentration, reaction temperature and reaction time on the synthesis of products
- Effect of nitric acid concentration on the product
A series of nitric acid concentration experiments were carried out at two temperatures. The reaction temperature of curve 1 was 160e and the reaction temperature of curve 2 was 180e. The product content was obtained by liquid chromatography (HPLC) normalization. It can be seen that with the decrease of nitric acid concentration, the content of p-tert-butylbenzoic acid increased, the concentration of nitric acid decreased to about 10%. When the temperature reached 180e, the content reaches the highest value. When the concentration of nitric acid was higher than 50%, we couldn’t obtain the desired product. In addition, in this experiment, it could also be seen the impact of temperature on the product. The content in the series of high temperature was significantly higher than that of the low temperature series.
- The effect of reaction temperature on the product
Considering the effect of reaction temperature, we selected the concentration of nitric acid at 10%. The effect of temperature on the product was that the reactant could not get the desired product at the reflux temperature. With the increase of temperature, the product content exhibits an increasing trend. At 170e, the content reaches the highest value with further increasing the temperature having almost no effect on the content.
- The effect of reaction time on the reaction
A large number of experiments have found that the reaction time only affects the reaction conversion rate, without affecting product selectivity. That is, it does not affect the content of the product and only affects the yield of the product. In the experiment, it can be clearly seen of that the reaction time is not enough when the reactor floating above a layer of liquid organic matter, the analysis is the raw material of tert-butyl toluene.
From the analysis of the data, we can see that the reaction temperature has the greatest influence on the yield. Considering various factors, we selected the reaction conditions as: the temperature: 180e, reaction time: 8h and nitric acid concentration: 10%. According to this condition, the content of p-tert-butylbenzoic acid was 98.4% and the yield was 95.5%.
Application
Important intermediates for organic synthesis.
Chemical Properties
CLEAR COLOURLESS TO YELLOW LIQUID
Uses
Methyl 4-
tert-butylbenzoate was used in the synthesis of
tris(4-
tert-butylphenyl)methyl chloride.
General Description
Methyl 4-t
ert-butylbenzoate undergoes Claisen condensation reaction with 4-methoxyacetophenone to give avobenzone, an ingredient of sunscreen products.
Synthesis
A comparison of synthesis methods for p-tert-butylbenzoic acid is presented, detailing the nitric acid oxidation method:
1. p-tert-Butyltoluene reacts with nitric acid in an autoclave at 180C for 8 h to give crude p-tert-butylbenzoic acid.
2. The crude product is dissolved in NaOH solution, filtered, and the filtrate is acidified (to pH ~3) to precipitate the purified acid.
