Tetraethylblei

Gefahreninformationscode (GHS)

• Bildanzeige (GHS)

  

• Alarmwort

  Achtung

• Gefahrenhinweise

  H373：Kann die Organe schädigen bei längerer oder wiederholter Exposition.

  H410：Sehr giftig für Wasserorganismen mit langfristiger Wirkung.

• Sicherheit

  P201：Vor Gebrauch besondere Anweisungen einholen.

  P260：Dampf/Aerosol/Nebel nicht einatmen.

  P280：Schutzhandschuhe/Schutzkleidung/Augenschutz tragen.

  P308+P313：BEI Exposition oder falls betroffen: Ärztlichen Rat einholen/ärztliche Hilfe hinzuziehen.

  P403+P233：An einem gut belüfteten Ort aufbewahren. Behälter dicht verschlossen halten.

TETRAETHYLLEAD Chemische Eigenschaften,Einsatz,Produktion Methoden

• ERSCHEINUNGSBILD

  FARBLOSE VISKOSE FLüSSIGKEIT MIT CHARAKTERISTISCHEM GERUCH.

• PHYSIKALISCHE GEFAHREN

  Die Dämpfe sind schwerer als Luft.

• CHEMISCHE GEFAHREN

  Zersetzung beim Erhitzen unter Bildung giftiger Rauche. Reagiert heftig mit starken Oxidationsmitteln, Säuren und Halogenen. Feuer- und Explosionsgefahr! Greift Gummi und einige Kunststoff- und Beschichtungsarten an.

• ARBEITSPLATZGRENZWERTE

  TLV: (als Blei) 0.1 mg/m? Hautresorption; Krebskategorie A4 (nicht klassifizierbar als krebserzeugend für den Menschen); (ACGIH 2005).
  MAK: (als Blei) 0.05 mg/m? Hautresorption; Spitzenbegrenzung: überschreitungsfaktor II(2); Hautresorption (H); Schwangerschaft: Gruppe B; (DFG 2008).
  

• AUFNAHMEWEGE

  Aufnahme in den Körper durch Inhalation, über die Haut und durch Verschlucken.

• INHALATIONSGEFAHREN

  Beim Verdampfen bei 20 °C kann schnell eine gesundheitsschädliche Kontamination der Luft eintreten.

• WIRKUNGEN BEI KURZZEITEXPOSITION

  WIRKUNGEN BEI KURZZEITEXPOSITION:
  Die Substanz reizt die Augen, die Haut und die Atmungsorgane. Möglich sind Auswirkungen auf das zentrale Nervensystem mit nachfolgender Bewusstlosigkeit. Exposition in hohen Konzentrationen kann zum Tode führen. ärztliche Beobachtung notwendig.

• WIRKUNGEN NACH WIEDERHOLTER ODER LANGZEITEXPOSITION

  Möglich sind Auswirkungen auf das zentrale Nervensystem. Kann fruchtbarkeitsschädigend oder entwicklungsschädigend wirken.

• LECKAGE

  Gefahrenbereich verlassen! Fachmann zu Rate ziehen! Belüftung. Ausgelaufene Flüssigkeit in abdichtbaren Behältern sammeln. Reste mit Sand oder inertem Absorptionsmittel aufnehmen und an einen sicheren Ort bringen. Persönliche Schutzausrüstung: Vollschutzanzug mit umgebungsluftunabhängigem Atemschutzgerät. NICHT in die Umwelt gelangen lassen.

• R-Sätze Betriebsanweisung:

  R61:Kann das Kind im Mutterleib schädigen.
  R26/27/28:Sehr giftig beim Einatmen, Verschlucken und Berührung mit der Haut.
  R33:Gefahr kumulativer Wirkungen.
  R50/53:Sehr giftig für Wasserorganismen, kann in Gewässern längerfristig schädliche Wirkungen haben.
  R62:Kann möglicherweise die Fortpflanzungsfähigkeit beeinträchtigen.
  R38:Reizt die Haut.
  R10:Entzündlich.

• S-Sätze Betriebsanweisung:

  S53:Exposition vermeiden - vor Gebrauch besondere Anweisungen einholen.
  S45:Bei Unfall oder Unwohlsein sofort Arzt zuziehen (wenn möglich, dieses Etikett vorzeigen).
  S60:Dieses Produkt und sein Behälter sind als gefährlicher Abfall zu entsorgen.
  S61:Freisetzung in die Umwelt vermeiden. Besondere Anweisungen einholen/Sicherheitsdatenblatt zu Rate ziehen.
  S36/37:Bei der Arbeit geeignete Schutzhandschuhe und Schutzkleidung tragen.
  S26:Bei Berührung mit den Augen sofort gründlich mit Wasser abspülen und Arzt konsultieren.

• Chemische Eigenschaften

  Tetraethyl lead is a colorless oily liquid. Sweet, slight musty odor. In commerce it is usually dyed red, orange or blue. Tetraethyl lead will decompose in bright sunlight yielding needlelike crystals of tri-, di-, and mono-ethyl lead compounds, which have a garlic odor.

• Chemische Eigenschaften

  colourless to yellow liquid

• Physikalische Eigenschaften

  Colorless liquid; burns with orange flame with green margin; refractive index 1.5198; density 1.653 g/mL at 20°C; insoluble in water; slightly soluble in ethanol; soluble in benzene, toluene, gasoline, and petroleum ether.

• Verwenden

  Tetraethyllead is used as an additive to gasolineto prevent knocking in motors. However,because of its high toxicity and the pollutionproblem, its use in gasoline has been drasticallycurtailed.

• Verwenden

  Anti-knock motor fuel additive

• Verwenden

  As a gasoline additive to prevent "knocking" in motors.Its use, however, is reduced drastically because of environmental pollution.

• synthetische

  Lead tetraethyl is prepared by heating ethyl chloride in the presence of a catalyst in an autoclave at 40 to 60°C with an alloy of lead and sodium:
  Pb + 4Na + 4C₂H₅Cl → Pb(C₂H₅)₄ + 4NaCl
  Also, it can be prepared by the reaction of lead with ethylene and hydrogen in the presence of Ziegler catalyst, triethylaluminum:
  Pb + 4C₂H₄ + 2H₂ → Pb(C₂H₅)₄

• Definition

  ChEBI: An organolead compound consisting of four ethyl groups joined to a central lead atom.

• Definition

  A poisonous liquid that is insoluble in water but soluble in organic solvents. It is manufactured by the reaction of an alloy of sodium and lead with 1-chloroethane. The product is obtained by steam distillation. Lead tetraethyl is used as an additive in internal-combustion engine fuel to increase its octane number and thus prevent preignition (knocking).

• Vorbereitung Methode

  These compounds were, at one time, the major industrial use of lead and source of environmental pollution of inorganic lead combustion products. However, the addition of these compounds to gasoline in the major industrialized countries of the world has been discontinued because of the use of catalysts for the control of the amount of nitrogen oxides in automobile exhaust. Organolead additives are still being phased out in many underdeveloped countries, although the United Nations has called for a global phaseout of lead in gasoline.

• Allgemeine Beschreibung

  A colorless liquid with a characteristic odor. Flash point 200°F. Density 14 lb / gal. Insoluble in water. Toxic by inhalation and by skin absorption.

• Air & Water Reaktionen

  Insoluble in water.

• Reaktivität anzeigen

  TETRAETHYL LEAD decomposes under UV light. Reacts with fats; reacts violently with oxidizing agents, causing fire and explosion hazards. Attacks rubber [Handling Chemicals Safely 1980. p. 890].

• Hazard

  Toxic by ingestion, inhalation, and skin absorption. Central nervous system impairment. Questionable carcinogen.

• Health Hazard

  Extremely poisonous; may be fatal if inhaled, swallowed, or absorbed from the skin. Contact may cause burns to skin and eyes. Most symptoms of poisoning are due to the effects of tetraethyllead on the nervous system.

• Health Hazard

  Tetraethyllead is highly toxic by oral route.The LD50 values for rats, mice, andrabbits were all found to be <15 mg/kgwhen administered by the oral, intravenous,subcutaneous, intraperitoneal, and parenteralroutes. It may be absorbed through theskin causing lead poisoning. It is toxic tothe central nervous system. The toxicity,however, is low to moderate by dermal route.It is an acute as well as chronic toxicant.The toxic effects are insomnia, hypotension,tremor, hypothermia, pallor, weight loss,hallucination, nausea, convulsion, and coma.The toxicity of this compound by inhalationroute is also low to moderate. Because of itslow vapor pressure, 0.2 torr at 20°C (68°F),inhalation hazard is relatively low.
  LD50 oral (rat): 12 mg/kg
  Oral lethal dose (rabbit): 30 mg/kg
  LC50 inhalation (rat): 850 mg/m³/1h.

• Brandgefahr

  May explode in fires. Decomposes slowly at room temperature and more rapidly at elevated temperatures.

• Sicherheitsprofil

  Human poison by an unspecified route. Experimental poison by ingestion, intraperitoneal, intravenous, subcutaneous, and parented routes. Moderately toxic by inhalation and skin contact. Experimental teratogenic and reproductive effects. Questionable carcinogen with experimental carcinogenic data. Mutation data reported. Lead compounds are particularly toxic to the central nervous system. It is a solvent for fatty materials and has some solvent action on rubber as well. The fact that it is a lipoid solvent makes it an industrial hazard because it can cause intoxication not only by inhalation but also by absorption through the skin. Decomposes when exposed to sunlight or allowed to evaporate; forms triethyl lead, which is also a poisonous compound, as one of its decomposition products. May cause elemental lead intoxication by coming in contact with the skin. A combustible liquid when exposed to heat, flame, or oxidizers. Can react vigorously with oxidzing materials. Exposure to air for several days may cause explosive decomposition. To fight fire, use dry chemical, CO2, mist, foam. When heated to decomposition it emits toxic fumes of Pb. See also LEAD COMPOUNDS.

• mögliche Exposition

  Tetraethyl lead is used as a component of antiknock mixes for gas and as an intermediate in making fungicides; Tetraethyl lead (used as an antiknock compound in gasoline) can also contains impurities, such as ethylene dibromide and ethylene dichloride.

• Carcinogenicity

  A case-control study of former workers in a TEL-producing plant found a strong association between exposure to the TEL manufacturing process and rectal cancer (the odds ratio was 3.7 with 90% confidence limits of 1.3–10.2 for the analysis of ever/never exposed to TEL). An exposure–response relationship was noted with a fourfold elevation in the odds ratio at the high–very high cumulative exposure level. Similar results were obtained for cancers of the sigmoid colon. These results suggest to the authors that exposure to the TEL manufacturing process may have played a causal role in the colorectal cancer findings in this plant. However, IARC in 2006 has included organolead compounds (TEL and TML), with Lead and its Compounds in Group 3, not classifiable as to its carcinogenicity to humans.

• Versand/Shipping

  UN1649 Motor fuel antiknock mixtures, Hazard Class: 6.1; Labels: 6.1-Poisonous materials.

• läuterung methode

  Its more volatile contaminants can be removed by exposure to a low pressure (by continuous pumping) for 1hour at 0o. Purify it by stirring with an equal volume of H2SO4 (d 1.40), keeping the temperature below 30o, repeating this process until the acid layer is colourless. It is then washed with dilute Na2CO3 and distilled water, dried with CaCl2 and fractionally distilled at low pressure under H2 or N2 [Calingaert Chem Rev 2 43 1926]. It prevents “knocking” in petrol combustion engines. [Milde & Beatty Adv Chem Res 23 306-318 1959, Beilstein 4 H 639.] VERY POISONOUS.

• Inkompatibilitäten

  Vapors may form explosive mixture with air. A strong reducing agent. Violent reaction with strong oxidizers, sulfuryl chloride; halogens, oils and fats; rust, potassium permanganate. Decomposes slowly in light and at room temperature, and more rapidly at temperatures above 110C. Attacks rubber and some plastics and coatings.

• Waste disposal

  Consult with environmental regulatory agencies for guidance on acceptable disposal practices. Generators of waste containing this contaminant (≥ 100 kg/mo) must conform with EPA regulations governing storage, transportation, treatment, and waste disposal. Controlled incineration with scrubbing for collection of lead oxides which may be recycled or land filled. It is also possible to recover alkyl lead compound from wastewaters as an alternative to disposal.

TETRAETHYLLEAD Upstream-Materialien And Downstream Produkte

78-00-2, TETRAETHYLLEAD Verwandte Suche: