142-71-2

A blue-green crystalline solid. The primary hazard is the threat to the environment. Immediate steps should be taken to limit its spread to the environment. CUPRIC ACETATE(142-71-2) is used as an insecticide, in the preparation of other chemicals, as a fungicide, and mildew preventive.

Salts, basic, such as CUPRIC ACETATE, are generally soluble in water. The resulting solutions contain moderate concentrations of hydroxide ions and have pH's greater than 7.0. They react as bases to neutralize acids. These neutralizations generate heat, but less or far less than is generated by neutralization of the bases in reactivity group 10 (Bases) and the neutralization of amines. They usually do not react as either oxidizing agents or reducing agents but such behavior is not impossible.

Water soluble.

Inhalation of dust causes irritation of throat and lungs. Ingestion of large amounts causes violent vomiting and purging, intense pain, collapse, coma, convulsions, and paralysis. Contact with solutions irritates eyes; contact with solid causes severe eye surface injury and irritation of skin.

Cupric acetate is used as a fungicide, as a catalyst for organic reactions; in textile dyeing and as a pigment for ceramics.

Special Hazards of Combustion Products: Irritating vapors of acetic acid may form in fires.

If this chemical gets into the eyes, remove any contact lenses at once and irrigate immediately for at least 15 minutes, occasionally lifting upper and lower lids. Seek medical attention immediately. If this chemical contacts the skin, remove contaminated clothing and wash immediately with soap and water. Seek medical attention immediately. If this chemical has been inhaled, remove from exposure, begin rescue breathing (using universal precautions, including resuscitation mask) if breathing has stopped and CPR if heart action has stopped. Transfer promptly to a Medical facility. When this chemical has been swallowed, get medical attention. Give large quantities of water and induce vomiting. Do not make an unconscious person vomit. Medical observation is recommended for 24 to 48 hours after breathing overexposure, as pulmonary edema may be delayed. As first aid for pulmonary edema, a doctor or authorized paramedic may consider administering a drug or other inhalation therapy.

UN3077 Environmentally hazardous substances, solid, n.o.s., Hazard class: 9; Labels: 9-Miscellaneous hazardous material, Technical Name Required.

Forms explosive materials with acetylene gas, ammonia, caustic solutions; sodium hypobromite; notromethane. Keep away from chemically active metals; strong acids; nitrates. Decomposes above 240C forming acetic acid fumes

Copper (II) acetate, also referred to as cupric acetate, is the chemical compound with the formula Cu(OAc)2₂ where OAc^- is acetate (CH₃CO₂^-). The hydrated derivative, which contains one molecule of water for each Cu atom, is available commercially. Anhydrous Cu(OAc)2 is a dark green crystalline solid, whereas Cu₂(OAc)₄(H₂O)₂ is more bluish-green. Since ancient times, copper acetates of some form have been used as fungicides and green pigments. Today, copper acetates are used as reagents for the synthesis of various inorganic and organic compounds. Copper acetate, like all copper compounds, emits a blue-green glow in a flame.

Cupric acetate is a greenish Blue powder or small crystals.

Green crystalline powder

Copper-containing soluble wastes can be concentrated through the use of ion exchange, reverse osmosis, or evaporators to the point where copper can be electrolytically removed and sent to a reclaiming firm. If recovery is not feasible, the copper can be precipitated through the use of caustics and the sludge deposited in a chemical waste landfill.

Copper (II) acetate was historically prepared in vineyards, since acetic acid is a byproduct of fermentation. Copper sheets were alternately layered with fermented grape skins and dregs left over from wine production and exposed to air. This would leave a blue substance on the outside of the sheet. This was then scraped off and dissolved in water. The resulting solid was used as a pigment, or combined with arsenic trioxide to form copper acetoarsenite, a powerful insecticide and fungicide called Paris Green or Schweinfurt Green.
During the Second World War copper acetate was used as shark repellent . Under war conditions, before adoption it has been tested only very briefly (while in general successfully). The source says copper acetate does repel sharks in some situations but not in all.

The uses for copper (II) acetate are more plentiful as a catalyst or oxidizing agent in organic syntheses. For example, Cu₂(OAc)₄ is used to couple two terminal alkynes to make a 1,3-diyne:
Cu₂(OAc)₄ + 2 RC ≡ CH → 2 CuOAc + RC ≡ C-C ≡ CR + 2 HOAc
The reaction proceeds via the intermediacy of copper(I) acetylides, which are then oxidized by the copper(II) acetate, releasing the acetylide radical. A related reaction involving copper acetylides is the synthesis of ynamines, terminal alkynes with amine groups using Cu₂(OAc)₄.

Copper (II) acetate synthesized by the method described in the history section leads to impure samples. It is prepared industrially by heating copper (II) hydroxide or copper (II) carbonate with acetic acid. A second method of copper acetate production is to electrolyze a concentrated aqueous solution of calcium acetate with copper electrodes. As the reaction proceeds the anode oxidizes to produce copper acetate which adheres to its surface and can be removed as crystals. At the cathode calcium ions are reduced to calcium atoms and would be deposited, but due to the water content of the solution the calcium is converted to insoluble calcium hydroxide. The drawback with this setup is that the cathode gets coated with an insulating layer of calcium hydroxide, which gradually slows the process. To negate this hydroxide buildup mercury is utilized as the cathode; therefore as the process takes place the calcium formed immediately reacts with the mercury to make a calcium-mercury amalgam and the copper acetate formed at the anode is removed periodically. This process generally yields suitably pure copper acetate, on a small scale, with slight traces of calcium acetate.
Copper (II) acetate also forms by treating copper metal with a solution of acetic acid and hydrogen peroxide.

Color Code—Green: General storage may be used.Prior to working with this chemical you should be trained on its proper handling and storage. Store in tightly closed containers in a cool, well-ventilated area. Cupric acetatemust be stored to avoid contact with acetylene gas, chemically active metals (such as potassium, sodium, magnesium,and zinc), since violent reactions occur

Recystallise it twice from warm dilute acetic acid solutions (5mL/g) by cooling. [Beilstein 2 IV 111.]